====================================
SiS900 Mass Production Test Program
====================================

(1) Introduction
================
  lantest.exe -- Test program (support multiple access through network)
  exlb.exe    -- Test program (with bigger font, no multiple access)
  ee.exe      -- EEPROM programming program 
  eesetup.exe -- Setup EEPROM data file for ee.exe 

  Note: ee.exe cannot support multiple access through network


(2) Modify EEPROM data file(ee) with EESETUP.EXE
==============================================
  1. Run eesetup.exe
     Ex: C:\> eesetup

  2. Create new EEPROM data file.
     Input :
             File name : EEPROM data file 
             OUI       : Organization Unique Id
             Start OUA : The first Id to be written to EEPROM
             Total Ids : How many Ids you want to use in this production line
                         (decimal)
             End OUA   : The last Id to be written to EEPROM
                         If you specify Count, you don't need to specify the
                         End OUA
          Sub_VendorID : Subsystem Vendor ID
          Sub_DeviceID : Subsystem Device ID

     Ex:
             File name : ee
             OUI       : 00E006 (hex)
             Start OUA : 000000 (hex)
             Total Ids : 2000   (decimal)
             End OUA   :        (not required)
          Sub_VendorID : 1039
          Sub_DeviceID : 0900                 

  3. Modify EEPROM data file.

     Note: When test is running, DO NOT use this to modify EEPROM data.

     You can see the current status in EEPROM data file.
             OUI         : Current OUI
             Start OUA   : The first Id
             Current OUA : Current Id
             Ids Used    : How many Ids was used in this production line
             Ids Left    : How many Ids left in this production line
             Total Ids   : Total Ids in this production line
             End OUA     : The last Id

      6 field you can modify:
             OUI         : If you need a new OUI
             Start OUA   : If you want to specify a new starting OUA
             Total Ids   : If you want to change the number of Ids in this
                           production line
             End OUA     :
            Sub_VendorID : Subsystem Vendor ID
            Sub_DeviceID : Subsystem Device ID

(3) Modify EEPROM data file(ee) manually
========================================
  1. Modify current address
     Ex: in EE, line 9, 10, 11
     e000
     0906     ===> 00 E0 06 09 00 01
     0100

     Modify starting address
     Ex: in EE, line 34
     00 E0 06 09 00 01

  2. Modify end address
     Ex: in EE, line 33
     00 E0 06 09 FF FF

(4) Program MAC address:
========================
    ee.exe -- Program MAC address
    Usage   : ee <eeprom_file>

    Ex:                              
    c:\>ee ee

(5) Test result:
================
  1. Pass: All tests are passed.
     ===> This LAN chip is good.

  2. Loopback test fail:
     The test program Logged failed MAC address to FailID file.
     ===> This LAN chip may not be good.
          You can re-use this MAC address.


(6) Other Usage:
================

 Two Station Test
   (i) LAN -- connect two stations with Ethernet cable
     Sender: Send packet and wait for response
       c:\>lantest /snd
     Responder: Listen packet from sender and send response to sender
       c:\>lantest /rsp


Change Notes :  -----------------------------------------------------------

                1) Lantest.exe -- ask user to specify LoopCount and Limit.
                               -- support 2 station test
                               -- support HomePNA

                   Usage : lantest <loopcount> <limit> [/option]
                   Option: /r --> Return directly

                2) exlb.exe    -- loopback test with different user interface
                               -- exlb needs a font file : modern.fon         
                   Usage : exlb <loopcount> <limit> [/option]
                   Option: /i --> Internal loopback only
                           /r --> Return directly
                
                3) ee.exe      -- add the function that not to advance to
                                  next MAC address and output log file

                   Usage   : ee <eeprom_file> [/Options] 
                   Options : /f --> fixed MAC address
                             /l --> output log file
                             /r --> restart system after programming MAC address

                4) eesetup     -- change the Power Management Control field
                                  in EEPROM from 0xfe01 to 0xfe02